Allrad-LKW-Gemeinschaft

Thanks Nils,for the reply.

Guten Tag, ich greife dieses Thema wieder auf. Übersetzung von Google. ich hoffe, Sie verstehen Nachdem ich den 1017 vier Jahre lang ausprobiert habe, habe ich das Gefühl, dass das Getriebe dazu führt, dass der Motor an Leistung verliert. :wack: Ich greife das Thema noch einmal auf, um zu sehen, ob ...

Thanks for the tips, i will not drill a hole on the diff. Better to see how is going now with the new seal. I will change the seal/joint of the sphere of the diff. Is dropping some grease from the balls. :blush: On the photo i took from net Epc the part i need is the number 170. Correct? Or usually ...

Thanks Pirx for the fast reply. Should i open a new hole for the pressure? My mechanic advise me to do it but i would like to gather some information before i do it! The Valvoline is new (4.000kms), but around 90kms per hour i fell some noises on the front diff. I did not have metal dust on the old ...

Google translate from last post. Hallo, Heute habe ich die Dichtung des vorderen Differentials gegen das Getriebe ausgetauscht. Beim Öffnen hatte das Differential etwas Druck. Vielleicht ist das der Grund, warum Valvoline ausläuft. Das Siegel konnte es nicht halten! Versucht, den Züchter auf dem Dif...

Hello, Today i changed the seal of front differential to the transmission. When opened the differential had some pressure. Maybe that is why the leak of Valvoline. The seal could not hold it! Tried to find the the breeder on the Diff but do not find it! Does this axles has breeder? Is normal the pre...

Hey Randy, thanks for the tip, i didn´t new which one to take. I used the gps track from a marrocain site http://www.djebel4x4.com/site/component/cwtags/24-fourgon-vert.html?Itemid=121 . On the Taouz-Tagounite there was one pass on soft dunes that i didn´t do. Stopped the truck and went to check by ...

Salam Alaikum, We just did the piste from Taoz - Foum Mharech - Tagounite. We did it in 4 days, (without guides just gps) enjoying the landscapes of sand dunes, lost oasis and rock mountains. Some parts of the journey were very hard, specially because the piste was full of stones. But on the sand th...

Salam Alaikum We are in Erg Chebi, parked on the dunes on the Northwest of the Erg. We are a family with one daughter of 8 years old traveling with our MB1017. We would like to find a partner truck to do the piste Taoz-Marech-Tagounite and later from M´hamid to Foum Any one around? Greetings from th...

Hello, Thanks DePo for the nice idea...i made a steel plate with 2 holes and worked perfectly. 78788856_1175558385969525_175549525434302464_n.jpg 78675665_656539661545910_915313511381336064_n.jpg 78705059_531549227429775_6170679986333155328_n.jpg Used the round tube to fit the seals 65/85/15,5 insid...

Olá, Tested (boiled) the thermostat and it start to open around 83º. Went for a drive without thermostat and soon the radiator was hot everywhere. The temperature of coolant around 50º and 3 kms up hill went almost to 80º. Conclusion: Thermostat good. Radiator good. Water pump good. Oil cooler good...

I put the first gear or the reverse to block the flange but i feel this is not the correct way. When i apply force to the nut, there is a elastic movement (does not block immediately) and the force goes until the back diff. I abandoned this idea. Also when i will take out the transmission from the g...

Hello, Mein VG500-Verteilergetriebe tropft Öl von den vorderen Getriebedichtungen. Ich möchte sie ersetzen, aber zuerst muss ich sowohl den Flansch als auch die Abdeckung herausnehmen. Weiß jemand, wie man die Muttern (24) aus den Flanschen herausnimmt? Und um sie zurückzusetzen, wie viel Kraft wird...

Hello, My VG500 transfer case is dripping oil from the front transmission seals. I want to replace them but first i must take both flange out, and the cover. Anyone knows how to take out the nuts (24) from the flanges? And to put them back how much is the force applied. 76655392_428692471404841_3680...

Hello Mark, When i changed the head gasket, new nozzles were installed on the injectors. I don´t like to drive on the limit of temperature...before i had a Om314 MB508D and the cruising was at 80º. Ok the owners book says that the engine runs at 95º and can run 10 minutes at 100º but i would prefer ...

Olá, Tested (boiled) the thermostat and it start to open around 83º. Went for a drive without thermostat and soon the radiator was hot everywhere. The temperature of coolant around 50º and 3 kms up hill went almost to 80º. Conclusion: Thermostat good. Radiator good. Water pump good. Oil cooler good....

Hello Chris,

I changed the water pump 2 days ago. Today i will boil the thermostat.

Hey, is possible to have a crack on the engine...i don´t discard it. Yet i don´t find oil or water mixed, but the temperature goes between 80º and 100º most of the time at 95º (above the parallel line of the floor). I am learning about this Co2 test. Thanks Pirx for the great pic. (very useful) now ...

Olá, So the thin tube from radiator is in the correct place? It should go from the top right side of the radiator to the expansion tank lid (valve). It stays on the middle of the valve (attached photos).?? I find the pressure there...the water coming out when i open the lid (valve)is from this thin ...

Hello, Yes Sascha, the cylinder head was tested on the shop! They said the cylinder head was leaking from the o-rings of the injectors bed. New o-rings fitted and new gasket from Elring. All the other gaskets was Victor Reinz. Yes Dapo, i fitted a new thermostat, and this one (Diesel Technic) has a ...

Hello.. My engine has a problem of pressure in the water system. Some months ago i found some oil on the water system so i opened the cylinder head , changed all the gaskets, water pump (Febi), thermostat, new refurbished radiator, new injector nozzles. Did not touch the engine block. I bleed the sy...

Hey, i read that health insurance must be made to enter Iran. Can be done on the border or will be more expensive? Never did health insurance to travel. Do you know where to do one? Greetings jenga Google translate Hallo, Ich habe gelesen, dass eine Krankenversicherung erforderlich ist, um in den Ir...

Hey, Thanks for the answers... more food for thoughts! I will learn more about the Raspberry Pi 3. I see now it has wire-less and can be used as router too. Is the Raspberry Pi easy to configure? Does anyone experience the Raspberry Pi as a router? W-lan and Gps antenna can be installed? Can i conne...

Moin, thanks for all the replies, is always good to check all possibilities. Would love to have Viprinet but is also very expensive and i don´t need a professional router. Would like to spend around 300€. ;) Mobile phones are a cheap solution but i am afraid that the antenna is not enough when we wi...

Hello, I am also searching for a LTE router wireless 4G to install on our truck. We plan to go to Asia and buy SIM cards everywhere. We need the internet to speak with family, to check online maps, videos, search places, surf internet and to upload videos. I read that the Teltonika RUT950 or 955 are...

Hey Gerd, This Spring hopefully we will drive to Nepal/India from Portugal with our 8 years old daughter and 11 year old male dog. The dog is educated but sure will give more worries than my daughter. I think the worst will be the strain dogs more than the people. But anyway i couldn´t go without hi...

Hello Bernd, I am Portuguese, live in Porto and since 2001 i drive around with my camper. Now i have a 1017AF that is almost ready to start my trip to Asia. Rules changed a lot since last years because the affluence of camper tourism next to the sea. Before we could park everywhere, next to the beac...

Thanks Wohnklo, i read this topic also, but my truck is a NG 1017AF and the conversion is different from the LN2 1317 in some details such as crossbeam, back support of gearbox, front kardanwelle.

Hello Brigitte and Roman Do you have a topic where you explain your engine and gearbox conversion? I would like to do the swap on my 1017AF the gearbox from G3 to GV4 but i don´t find enough information. My fear is the length of the gearbox that will not fit the PTO, and also the new crossbeam that ...

Hello, Thanks Wilmaaa, i will try to resize the pics before i upload them. Stefan, i bought the screws from Victor Reinz but they have star heads. The original were Hezagon. Do you think Victor Reinz screws are not good for OM352? The Zylinderkopf has 8 screws and 2 of them tight to the head screws....